Order Cart | Contact Us | Home | SIGs | Login
Kits:

HackRF One

HackRF One Info

HackRF One from Great Scott Gadgets is a Software Defined Radio peripheral capable of transmission or reception of radio signals from 10 MHz to 6 GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation.

  • 1 MHz to 6 GHz operating frequency
  • half-duplex transceiver
  • up to 20 million samples per second
  • 8-bit quadrature samples (8-bit I and 8-bit Q)
  • compatible with GNU Radio, SDR#, and more
  • software-configurable RX and TX gain and baseband filter
  • software-controlled antenna port power (50 mA at 3.3 V)
  • SMA female antenna connector
  • SMA female clock input and output for synchronization
  • convenient buttons for programming
  • internal pin headers for expansion
  • Hi-Speed USB 2.0
  • USB-powered
  • open source hardware

HackRF One has an injection molded plastic enclosure and ships with a micro USB cable. An antenna is not included. ANT500 is recommended as a starter antenna for HackRF One.

HackRF One is test equipment for RF systems. It has not been tested for compliance with regulations governing transmission of radio signals. You are responsible for using your HackRF One legally.

Documentation Wiki

Ordering Information

The price for the HackRF One is:

  • $ 299 USD

(Place Web Order)

A note regarding email addresses: When checking out please use an email address other than @earthlink.net, @hotmail.com, @live.com, @msn.com, @outlook.com. For some reason these domains reject email from tapr.org
ALSO There is a problem with Chrome inaccurately reporting that the connection is insecure when you are attempting to complete your order. We suggest using a different browser to place the order.
Both problems are being worked on, sorry for the inconvenience.

Shipping and Handling

Shipping and Handling within the US will be by USPS Priority Mail.

International shipping costs are calculated as closely as possible. If the actual cost exceeds the estimate by more than $10.00, TAPR will contact you to get approval for the additional funds. TAPR uses insured Priority Mail International, unless the purchaser requires something else.


ANT500

ANT500 from Great Scott Gadgets is a telescopic antenna designed for operation from 75 MHz to 1 GHz. Its total length is configurable from 20 cm (7.9") to 88 cm (34.6"). ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow.

ANT500 is a 50 ohm antenna designed to match HackRF One. It is the perfect first antenna for general purpose use with HackRF One.

Ordering Information

The price for the AT500 Antenna is:

  • $ 29 USD

(Place Web Order)

A note regarding email addresses: When checking out please use an email address other than @earthlink.net, @hotmail.com, @live.com, @msn.com, @outlook.com. For some reason these domains reject email from tapr.org
ALSO There is a problem with Chrome inaccurately reporting that the connection is insecure when you are attempting to complete your order. We suggest using a different browser to place the order.
Both problems are being worked on, sorry for the inconvenience.

Shipping and Handling

Shipping and Handling within the US will be by USPS Priority Mail.

International shipping costs are calculated as closely as possible. If the actual cost exceeds the estimate by more than $10.00, TAPR will contact you to get approval for the additional funds. TAPR uses insured Priority Mail International, unless the purchaser requires something else.


Acrylic Case for HackRF One

Acrylic Case for HackRF One photo

This acrylic case features cutouts that allow users to access the expansion headers on the board, and comes packaged with assembly hardware, a spudger for extracting the board from its standard case, and a HackRF One sticker.

Assembly Instructions

Warning: Do not overtighten! Hand-tighten only at every step.

  1. Use a guitar pick or spudger to extract the HackRF One circuit board from the black plastic case.
  2. Insert one long screw into each corner of the bottom acrylic panel. Secure each long screw with a short (5 mm) spacer on the opposite side of the panel.
  3. Place the HackRF One circuit board (facing up) on top of the bottom panel, fitting the ends of the long screws through the corner mounting holes of the circuit board.
  4. Secure the circuit board with one long (6 mm) spacer in each corner.
  5. Place the top acrylic panel on top of the circuit board, aligning the cutouts with the circuit board's expansion headers.
  6. Secure each corner with a short screw.

Ordering Information

The price for the HackRF One Acrylic Case is:

  • $ 15 USD

(Place Web Order)

A note regarding email addresses: When checking out please use an email address other than @earthlink.net, @hotmail.com, @live.com, @msn.com, @outlook.com. For some reason these domains reject email from tapr.org
ALSO There is a problem with Chrome inaccurately reporting that the connection is insecure when you are attempting to complete your order. We suggest using a different browser to place the order.
Both problems are being worked on, sorry for the inconvenience.

Shipping and Handling

Shipping and Handling within the US will be by USPS Priority Mail.

International shipping costs are calculated as closely as possible. If the actual cost exceeds the estimate by more than $10.00, TAPR will contact you to get approval for the additional funds. TAPR uses insured Priority Mail International, unless the purchaser requires something else.


Acrylic Case Installation

If you'd like to have the Acrylic Case installed on your new HackRF One, we can do that for you.

Ordering Information

The price for the Acrylic Case Installation is:

  • $ 15 USD

(Place Web Order)

A note regarding email addresses: When checking out please use an email address other than @earthlink.net, @hotmail.com, @live.com, @msn.com, @outlook.com. For some reason these domains reject email from tapr.org
ALSO There is a problem with Chrome inaccurately reporting that the connection is insecure when you are attempting to complete your order. We suggest using a different browser to place the order.
Both problems are being worked on, sorry for the inconvenience.

Shipping and Handling

Shipping and Handling within the US will be by USPS Priority Mail.

International shipping costs are calculated as closely as possible. If the actual cost exceeds the estimate by more than $10.00, TAPR will contact you to get approval for the additional funds. TAPR uses insured Priority Mail International, unless the purchaser requires something else.


Fequently Asked Questions

Start up FAQ will help you get started with your HackRF One.

About Us | Privacy Policy | Contact Us | ©2005-2017 Tucson Amateur Packet Radio Corp unless otherwise noted.

facebook twitter utube

Accept Credit Cards