Order Tray | Contact Us | Home | SIG Lists

[aprssig] agwpe and d700

kb2scs at optonline.net kb2scs at optonline.net
Sat Feb 26 22:02:52 UTC 2005


Hi Wes 
             The commands are.
KISS ON 
RESTART

Not RESET

I am not shouting just showing the commands in uppercase.

On 26 Feb 2005 at 16:30, Wes Johnston wrote:

> Ken, today I tried to use the TNC2 template to setup the d700 into kiss mode,
> and it was a no-go.  I used hyperterm to see and interact with the TNC/radio
> and observed that entering KISS ON, and typing RESET did not cause 
the tnc to
> go into KISS mode - it simple reset and gave the usual TNC2 
compatible boot
> screen.  However, entering KISS ON, and cycling the power off and 
back on did. 
> Is there any way to reset the TNC (to finish the kiss mode switch) 
with out
> having to power cycle the radio?
> 
> FWIW to anyone reading this thread, the default TXD is 500mS... 
holy smokes...
> not even 350ms!!! I'm going to play with mine to see if it'll work 
near the
> 100mS mark.
> 
> Thanks
> Wes
> --
> 
> 
> 
> Quoting Ken Collins <g4fip at tiscali.co.uk>:
> 
> > In message <1109291807.421e731f2710c at www.kd4rdb.com>, Wes 
Johnston
> > <aprs at kd4rdb.com> writes
> > >Can anyone point me to a quick setup guide to get the kenwood 
d700
> > >working in kiss mode with agwpe?  Or advise about the commands 
to go
> > >from TNC PKT on front panel to kiss mode on internal TNC?
> >
> > Run AGWPE. This will create a small twin antenna icon in your 
systray
> >
> > 1.      Click on that icon and select Properties.
> > 2.      Create a New Port and setup the COM port and TNC. Use
> >              the TNC2 option from the TNC selection list. Click 
on OK.
> > 3.      Click on the systray icon again.
> > 4.      Select Setup Interfaces and enable Winsock TCP/IP 
Application
> >              Interface with a TCP port of 8000 and click OK.
> >
> > You will now have to exit and restart AGWPE.
> >
> >  From here on, every time you start AGWPE the D700 will 
automatically go
> > into KISS mode. Conversely when you close AGWPE it will exit KISS 
mode.
> >
> > Sounds a lot but it is very simple to do and the setup should 
only take
> > you a couple of minutes.
> >
> >
> > --
> > Ken Collins - G4FIP
> > E-mail:- g4fip at tiscali.co.uk
> >
> > _______________________________________________
> > aprssig mailing list
> > aprssig at lists.tapr.org
> > https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig
> >
> 
> 
> _______________________________________________
> aprssig mailing list
> aprssig at lists.tapr.org
> https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig


Let us hope we never witness the "Silence Of The Hams"
73 DE John  KB2SCS
       E-Mail:            kb2scs at arrl.net
       APRS-SCS     http://www.tapr.org/~kb2scs
       Web Page:     http://www.qsl.net/kb2scs




More information about the aprssig mailing list