[aprssig] Out of memory

[Sam Guccione]

Thanks for the response Earl. I used tabs but that made no difference.

Sam

-----Original Message-----
From: aprssig-bounces at lists.tapr.org
[mailto:aprssig-bounces at lists.tapr.org]On Behalf Of Earl Needham
Sent: Sunday, June 19, 2005 10:58 PM
To: TAPR APRS Mailing List
Subject: RE: [aprssig] Out of memory



         Make sure the fields are separated by tabs.  Other than that, I'm
out of ideas.

         7 3
         Earl

At 09:05 PM 6/19/2005, Sam Guccione wrote:
>Well I am not sure what is happening but my WinAPRS installation does not
>seem to find the config.txt or memory.txt file I created in the WinAPRS
>directory because I get the Out of memory message after the station list
>gets to 4096 when I have STATIONS in the config file set to 16384.
>
>Any ideas on what to try next?
>
>Sam K3BY
>-----Original Message-----
>From: aprssig-bounces at lists.tapr.org
>[mailto:aprssig-bounces at lists.tapr.org]On Behalf Of Earl Needham
>Sent: Saturday, June 18, 2005 9:43 AM
>To: TAPR APRS Mailing List
>Subject: Re: [aprssig] Out of memory
>
>At 08:11 AM 6/18/2005, I wrote:
>
>>         It's been a while since I ran WinAPRS, but I have a file in my
>> WinAPRS folder called "memory.txt" and it contains the following:
>>
>>STATIONS        16382
>>MESSAGES        16382
>>PKTBUFFER       2000192
>>DESTROYICONS    YES
>>
>>         I'm not really sure these are valid settings, but you might give
>> them a try.
>
>         I was able to find the following in the WinAPRS documentation:
>
>
>
>memory.txt or config.txt
>
>
>
>Either file name can be used. It will look for config.txt first, then look
>for memory.txt. Only one will be read. Since users need to be able to
>configure the amount of memory being allocated for station lists etc,
>before the program is launched and even if they are not registered, a
>separate config file is set up for this purpose. It is memory.txt. It must
>be located in the same directory as the WinAPRS.exe application. It can
>contain the following commands. Use a single TAB to separate the command
>and the argument.
>STATIONS n - this tells it how many stations to allocate
>MESSAGES n - this tells it how many messages to allocate
>PKTBUFFER n - how much memory to allocate for the packet buffer (8192
>minimum)
>DESTROYICONS YES/NO - this is for WinAPRS ONLY and is to help debug memory
>problems.
>Version 2.4.0 and 2.4.1 did not destroy icons, version 2.4.2 did. This
>will allow users to change the setting so that we can figure out what
>works and what does not.
>If the memory.txt file is not present, it will default to the normal
>station counts that it did in version 2.4.2.
>
>         7 3
>         Earl
>
>
>Earl Needham, KD5XB, Clovis, New Mexico DM84jk
>http://kd5xb-2.no-ip.info
>
>_______________________________________________
>aprssig mailing list
>aprssig at lists.tapr.org
>https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig



_______________________________________________
aprssig mailing list
aprssig at lists.tapr.org
https://lists.tapr.org/cgi-bin/mailman/listinfo/aprssig