Order Tray | Contact Us | Home | SIG Lists

[aprssig] Out of memory

Sam Guccione gucci1 at mchsi.com
Wed Jun 22 23:06:02 UTC 2005


I placed them in the c:\WinAPRS directory where it says they should go.

  -----Original Message-----
  From: aprssig-bounces at lists.tapr.org
[mailto:aprssig-bounces at lists.tapr.org]On Behalf Of Keith Kotch
  Sent: Wednesday, June 22, 2005 7:35 AM
  To: 'TAPR APRS Mailing List'
  Subject: RE: [aprssig] Out of memory


  Show us the complete path you have for those 2 files.  That may help
troubleshoot what's wrong.  I suspect it's where you placed those files.



  Keith, KF4BXT




----------------------------------------------------------------------------
--

  From: aprssig-bounces at lists.tapr.org
[mailto:aprssig-bounces at lists.tapr.org] On Behalf Of Sam Guccione
  Sent: Sunday, June 19, 2005 11:05 PM
  To: TAPR APRS Mailing List
  Subject: RE: [aprssig] Out of memory



  Well I am not sure what is happening but my WinAPRS installation does not
seem to find the config.txt or memory.txt file I created in the WinAPRS
directory because I get the Out of memory message after the station list
gets to 4096 when I have STATIONS in the config file set to 16384.



  Any ideas on what to try next?



  Sam K3BY

    -----Original Message-----
    From: aprssig-bounces at lists.tapr.org
[mailto:aprssig-bounces at lists.tapr.org]On Behalf Of Earl Needham
    Sent: Saturday, June 18, 2005 9:43 AM
    To: TAPR APRS Mailing List
    Subject: Re: [aprssig] Out of memory

    At 08:11 AM 6/18/2005, I wrote:




            It's been a while since I ran WinAPRS, but I have a file in my
WinAPRS folder called "memory.txt" and it contains the following:

    STATIONS        16382
    MESSAGES        16382
    PKTBUFFER       2000192
    DESTROYICONS    YES

            I'm not really sure these are valid settings, but you might give
them a try.


            I was able to find the following in the WinAPRS documentation:

    memory.txt or config.txt
    Either file name can be used. It will look for config.txt first, then
look for memory.txt. Only one will be read. Since users need to be able to
configure the amount of memory being allocated for station lists etc, before
the program is launched and even if they are not registered, a separate
config file is set up for this purpose. It is memory.txt. It must be located
in the same directory as the WinAPRS.exe application. It can contain the
following commands. Use a single TAB to separate the command and the
argument.

      a.. STATIONS n - this tells it how many stations to allocate
      b.. MESSAGES n - this tells it how many messages to allocate
      c.. PKTBUFFER n - how much memory to allocate for the packet buffer
(8192 minimum)
      d.. DESTROYICONS YES/NO - this is for WinAPRS ONLY and is to help
debug memory problems.
      e.. Version 2.4.0 and 2.4.1 did not destroy icons, version 2.4.2 did.
This will allow users to change the setting so that we can figure out what
works and what does not.
    If the memory.txt file is not present, it will default to the normal
station counts that it did in version 2.4.2.

            7 3
            Earl



    Earl Needham, KD5XB, Clovis, New Mexico DM84jk

    http://kd5xb-2.no-ip.info
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.tapr.org/pipermail/aprssig/attachments/20050622/cc609192/attachment.htm 


More information about the aprssig mailing list