[aprssig] KPC3+ induced errors
ve7gdh at rac.ca
Wed Mar 16 13:33:04 CDT 2011
Larry K0ANI wrote...
> You asked about the Igater that was using the Kenwood D710 on the EOSS
> flights Saturday. It was Mark, KC0D, a well know and very competent HAM.
> He was running his Igate unattended as he was out in the field as part of
> the Tracking and Recovery team. We have had conversations about this issue
> and he is at a loss for what is happening as are we all.
Looking below, where was the EOSS digi located? Was it on the ground
or in the air?
> Here is a snapshot of the telemetry from EOSS-159, the first flight of the
> day. Mark's Igate is kc0d-3 in the snapshot. I haven't broken out the
> delays to measure the delay time, but I don't think it matters as there is
> an obvious problem that can be seen in the time stamps and the altitudes
Keep in mind that it the data below was obtained from the APRS-IS, there could be a lot
of dupes that were thrown out. If dupes were delayed by more than 30 seconds, they would
show up on the APRS-IS.
Note the time stamps in the $GPGGA sentences.
The 135346 beacon was obviously sent after the one at 135316 and before the one at 140228
but was gated after the 140228 beacon. The first and third beacons above were gated by KC0D-3,
but the one in between was gated by KC0VJE. I don't see an asterisk by the EOSS digi, so I'm
assuming that all three above were heard direct.
I searched all of the beacons that you posted. There weren't any duplicates, but going by the
time stamps, some were out of order. Do you know if the EOSS digi was used for any of the
beacons? Just going by the data that you posted, it was not... i.e. there wasn't an asterisk by
it indicating that the digi path had been used. If that is correct, the delays would be attributed
to the IGate... whether it was the TNC or the IGate software being used would have to be
Fortunately, the data for KC0YA-11 can still be seen at aprs.fi...
I can see the beacon from 135346 gated by KC0VJE at 13:53:51 UTC. It was gated again
by KC0D-3 at 14:02:59 UTC, showing a delay of about 10 minutes. I don't see any asterisk
indicating that the digi path was used. I'll paste the two beacons below.
2011-03-12 13:53:51 UTC:
2011-03-12 14:02:59 UTC:
[Location changes too fast (>500 km/h)]
Because raw data is only available for a few days on aprs.fi, I just grabbed all that
was available, amounting to the last 900 beacons. I've saved it in a text file here, so that
will always be available. Searching the page for an asterisk by the digi path, I see
that that EOSS was never used. However, some beacons were to APRS and some
were to BEACON. The ones sent to BEACON were telemetry beacons, and they
went out with a path of WIDE2-2.
Focusing on one of the later beacons...
2011-03-12 16:10:53 UTC:
The time stamp according to the beacon was 161047. It was digi'd by AEOSS-11 and
gated by N0PSJ 6 seconds later at 16:10:53 UTC. The same beacon was then gated
2011-03-12 16:14:19 UTC:
Both N0PSJ and KC0D-3 heard it via the AEOSS-11 digi, so any delay introduced
by the digi would be seen by both IGates... in other words, the two IGates heard the
beacon from the digi at the same time. The second copy was gated at 16:14:19 which
works out to a delay of 3 minutes 26 seconds. Perhaps some coordinated tests
could be done with KC0D-3. I've done this in the past. Just get together on UHF or HF
or whatever, send a beacon, preferably with a time stamp, and get KC0D-3 to watch
the IGate and tell you when he sees the beacon. He appears to be running UI-View, so
it should be an easy matter for him to open the terminal window and set the filter
to exclude "Internet" traffic (this is the terminal window filter, not the one used to
connect to the APRS-IS) so he is watch RF traffic only to makes things easier to
Does anyone know of any software that can receive data on a serial port and spit
it out on a different virtual port? I'm just trying to think of a way for KC0D-3 to view
the serial data even before it gets to UI-View. I suppose a "low tech" way of seeing
delays would be to watch the S meter on the radio and then watch the terminal
window to see when the beacon shows up there. For delays that were in the
minutes instead of seconds, a check somewhere like aprs.fi (that really gets data
from the APRS-IS) could provide a further confirmation that the beacon got to the
APRS-IS moments after it was seen in the terminal window.
73 es cul - Keith VE7GDH
"I may be lost, but I know exactly where I am!"
More information about the aprssig