[aprssig] APRS = the AoT of Amateur Radio [was: APRS to the planet rescue?

Robert Bruninga bruninga at usna.edu
Tue Apr 11 19:53:29 CDT 2017


Way to go Scott!

Yes, I'm ready to roll on the AoT, (APRS of things)!  As our government and
its followers turns towards greed and self interest and profit over science
and knowledge and the protection of our environment, we are just going to
have to do what we can ourselves.

We'll probably have to carve out a different frequency to protect our
throughput on 144,39, but that will come when needed.

I sure wish there were cheap modules on 6m!  The path loss for Omni to Omni
is 8 dB better than 2m and 16 dB better than UHF (though the higher noise
floor eats up most of that.

I want theses things:
* water gauge, (flood gauge)
* Methane detector
* Radiation detector
* Radon Detetctor
* Carbon monoxide
* Smoke
* others?

And I want a TX only unit and a 2-way unit for building the mesh DIGI
network.

Bob, WB4APR

On Tue, Apr 11, 2017 at 8:06 PM, Scott Miller <scott at opentrac.org> wrote:

> I remember seeing an APRS flood monitor at Dayton a few years ago.  They
> weren't particularly cheap devices, but I think they used ultrasonic
> gauges.  A simple float switch would do it.
>
> The DRA818V (and probably others) transceiver modules have finally started
> to make a lot of these applications cheap and practical on 2 meters without
> resorting to scavenged HTs.  They're under $15 and good for at least half a
> watt of TX power, or a full watt if you believe the data sheet.
>
> My current project isn't focusing on low power consumption right now, but
> without any effort at power saving it's still not too bad - I just tested
> it at about 80 mA @ 5 volts with WiFi connected and idle.
>
> I'll definitely work on getting something out there to cover the low power
> sensor mesh stuff.  Having a high-level scripting language geared
> specifically for APRS and radio applications should make it a lot easier to
> tackle some of these projects than starting from scratch with an Arduino,
> with a lot less power consumption than a single-board computer like a
> Raspberry Pi.
>
> Some of this I'm going to do for myself, market viability be damned,
> because I've got too many little sensor and remote monitoring and control
> projects of my own that don't rate custom hardware and firmware.  Even if
> no one else ever buys any, I'm going to have a shelf full of complete APRS
> gadgets that I can use to throw together just about anything without having
> to compile any code.
>
> Scott
> N1VG
>
> On 4/6/2017 7:24 AM, Ev Tupis wrote:
>
> Very interesting, Scott.  This seems like a fairly complex device with
> lots of capability.  I'll be watching from afar to see how it progresses.
>
> Interestingly, the local ARES group has a text-message system that just
> sent out the following for my area...
>
> "The Storm Trackers Team continues the Potential Alert for General
> Flooding for all of our area from thru Sat. midday.  Periods of rain
> continues into Friday night.  Snow mixes in Friday.  Rainfall of 1 to 2.5
> inches is likely which can cause flooding.  If you live in a flood prone
> area, remain alert!"
>
> Here is where the IoT of amateur radio (if it existed) could offer huge
> value...if we only had sensors to deploy *and* a robust APRS network to
> deliver the data.
>
> I imagine a variation of a common "floor wet monitor" that you find in a
> hardware store that...
>
> * can be deployed to a "flood prone" area, attached to a stake in the
> ground
> * would send a "flood stage" beacon once water was detected "at that level"
> * could be deployed during these events and removed afterward
> * run on a 9V battery (or maybe two)
> * with an algorithm to minimize battery consumption while still providing
> useful data
> * (maybe) could be cheap enough to be "throw aways" in case they are
> "swept away" (or stolen?)
>
> I'm thinking small, inexpensive, deployable ... and a "bridge" to send
> that data to a municipality's "command center".
>
> I'm also thinking about what it would take for the ARRL to ask their
> Emcomm person to pursue DHS or NOAA grants to fund development if needed.
>
> THIS would be a big step in making amateur radio relevant again, in the
> eyes of the sworn-officer and professional EFR community.
>
> Ev, W2EV
>
>
>
>
> On Tuesday, April 4, 2017, 9:36:46 AM EDT, Scott Miller
> <scott at opentrac.org> <scott at opentrac.org> wrote:
> I'm definitely headed down the IoT/M2M path with the stuff I'm working on
> now.  This is what's on my desk now:
>
> http://imgur.com/2M8Xs9K
>
> This is the successor to both the Tracker3 line and the ADS-SR1 repeater.
> It has two radio ports (and will add at least a third RX-only port to meet
> repeater control requirements), WiFi (not in the small version), including
> the ability to function as an access point, USB (virtual COM port and mass
> storage at this point), RS-232, and RS-485.
>
> It'll do a bunch of conventional TNC and repeater controller things,
> including operating as a dual-port simplex repeater, cross-band repeater,
> duplex repeater, and some weird hybrid modes.  It'll operate as a TNC,
> digipeater, and standalone IGate.
>
> The RS-485 port is set up for Modbus RTU and will interface with all sorts
> of off the shelf sensors, relays, I/O modules, motor controllers,
> actuators, and whatnot.  The small board connected to it here is an
> interface for our wind and rain sensor assembly.  I've been testing it with
> everything from $8 quad relay boards to $400 Acromag industrial I/O modules.
>
> It has a BASIC interpreter with high-level commands for handling voice,
> APRS, and Modbus.  It's particularly useful for data transformation tasks -
> one demo pulls raw Modbus temperature and humidity readings and converts
> them to floating point values in the required units, and you can build APRS
> packets with the string handling functions.
>
> You could have a BASIC script watch a Modbus temperature sensor and door
> switch and when something of interest happens send an APRS message over one
> radio port, play a series of WAV files on another radio port, and use HTTPS
> to send JSON data to a service like Twilio to send a text message to your
> phone.
>
> I'm looking into the feasibility of making it Echolink-compatible, but
> usable technical information on Echolink is scarce.  If anyone knows of any
> protocol specification, please let me know.  It looks like it's using the
> GSM full-rate codec over RTP, but I don't know anything about the
> signalling protocol.
>
> All of this is stuff you could do with a Raspberry Pi and a pile of
> adapters and some shell scripts, but I'm trying to make it one ready-to-use
> box with a scripting system geared toward non-programmers.
>
> It's got months of work to go still, but a few units are out there for
> beta testing as repeaters already.  I'm hoping to have something ready to
> release to the APRS community this summer.
>
> Scott
> N1VG
>
> On 4/4/2017 8:25 AM, Ev Tupis wrote:
>
> So here is where I chime in (again).  Several years ago (at the "Emcomm
> East" convention), I presented on the topic "Growing APRS' Value to the
> First Responder Community".
>
> The points that I made there hold true even more today: Emcomm is not what
> it was in the 1980's.  EFR's don't need us to pass traffic.
>
> Our value comes from "outside of the yellow tape".
>
> Enter: APRS as the IoT/M2M of the Emcomm world
>
> We need to provide situational awareness that is not available in any
> other way.  We need sensors that are both housed at our homes *and*
> reporting via APRS *and* batter backed up ... and we need sensors that we
> can deploy around the perimeter of an event to report conditions via APRS
> ... and we need an APRS infrastructure with a gateway to the EFR's "dot on
> a map" system.
>
> If you still think otherwise, then please tell me specifically...when was
> the last time you were activated and did anything OTHER than open an HF net
> and take check-ins?  A rhetorical question as someone in some special case
> may come up with one or two instances...but let's be honest...that is all
> that happens a VAST majority of the time.
>
> I have asked the ARRL each time they touted an ARES activation, "This
> looks like a news story about the disaster, but what did we actually do?"
> Answer: setup an HF net and took checkins.  (yawn).
>
> I asked here, "When were you deployed and used APRS?".  The answers I
> received were not Emcomm related...they were public service related.  It is
> only a matter of time until even public service organizations can do it
> themselves, too.
>
> It is time to reinvent.  How do we build inexpensive, callibrated,
> deployable sensors and regain our worth to the Emcomm community?
>
> Ev, W2EV
>
>
>
> Inspired by the post below...
>
> On Monday, April 3, 2017, 8:04:38 PM EDT, Scott Miller
> <scott at opentrac.org> <scott at opentrac.org> wrote:
> Throwing a bunch of uncalibrated sensors out there with no standards for
> their placement is not going to get you much useful data.  It might be fun
> to look at your own track and see where you get hot spots but it's not
> going to do serious researchers much good.
>
> And didn't we discuss a standardized type-length-value extension scheme a
> while back?  Aside from OpenTRAC, that is.  At the very least I think any
> more extensions to the format need a formal definition, maybe a BNF
> grammar, to guarantee that everything is unambiguous and parseable.
>
> Scott
> N1VG
>
>
>
>
> _______________________________________________
> aprssig mailing listaprssig at tapr.orghttp://www.tapr.org/mailman/listinfo/aprssig
>
>
>
> _______________________________________________
> aprssig mailing list
> aprssig at tapr.org
> http://www.tapr.org/mailman/listinfo/aprssig
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tapr.org/pipermail/aprssig/attachments/20170411/c71db2b5/attachment.html>


More information about the aprssig mailing list