[vna] Uncalibrated message

[tom.mcdermott4 at sbcglobal.net]

Thanks, Stan.

Wow, that one's going to take awhile to find, as the error message is
not generated by the VNA application, but within (I guess) some Microsoft
software somewhere.  MS's error message is as unhelpful to me as it
is to you!  Sounds like time to, post a query on the MS development
boards...

	-- Tom, N5EG





> -----Original Message-----
> From: vna-bounces at lists.tapr.org 
> [mailto:vna-bounces at lists.tapr.org] On Behalf Of Stan Rife
> Sent: Monday, November 13, 2006 6:07 PM
> To: 'TAPR/Ten-Tec VNA Users List'
> Subject: RE: [vna] Uncalibrated message
> 
> 
> 	Ok, Tom. I had the .net 2.0 installed, and had no luck 
> with the Beta
> 2.0. I uninstalled the V2.0 .net and reinstalled the latest 
> version just to
> be sure. Still no luck with the Beta.
> 
> 	I just tried it again so I could get the error message 
> (which I am
> attaching), and it acted different this time, in that it went out and
> downloaded .net 2.0 and installed it before installing the 
> VNA package. I
> still get the error though.
> 
> 
> Stan Rife
> W5EWA
> Houston, TX
> K2 S/N 4216
>  
> 
> -----Original Message-----
> From: vna-bounces at lists.tapr.org 
> [mailto:vna-bounces at lists.tapr.org] On
> Behalf Of tom.mcdermott4 at sbcglobal.net
> Sent: Monday, November 13, 2006 5:36 PM
> To: 'TAPR/Ten-Tec VNA Users List'
> Subject: RE: [vna] Uncalibrated message
> 
> 
> Stan,
> 
> 	the Beta 2.0 requires the installation of the Microsoft
> .NET 2.0 runtime (all older version of the VNA software Use .NET 1.1).
>  MS installer should check whether or not it's installed on 
> your machine.
> Can you tell me more about the error you receive when you try to
> Run the Beta 2.0 of the VNA software?  Can you capture a screenshot?
> 
> 	-- Tom, N5EG
> 
> 
> 
> 
> 
> > -----Original Message-----
> > From: vna-bounces at lists.tapr.org 
> > [mailto:vna-bounces at lists.tapr.org] On Behalf Of Stan Rife
> > Sent: Sunday, November 12, 2006 1:55 PM
> > To: vna at lists.tapr.org
> > Subject: [vna] Uncalibrated message
> > 
> > 
> > 	After calibration of the Detector and a fixture 
> > calibration, I still
> > have the "Uncalibrated" message in the upper left hand corner 
> > of the screen.
> > I am running V1.5 of the software on my desktop computer, as 
> > well as V1.6 on
> > my laptop. I have been through the calibration steps on both 
> > computers and
> > get the same behavior. Also, after I do a sweep and then 
> > click on "apply
> > calibration" I see no, or very little, correction on the trace. 
> > 
> > 	On another note, I have tried several times to install 
> > the Beta V2.0
> > with no luck. It appears to install ok, but when I start the 
> > program it
> > gives me an error message about the configuration not being 
> > correct. Is
> > there something missing? I did notice that there is not a 
> > configuration file
> > with the setup files as in V1.5 & V1.6.
> > 
> > 	I have to tell you that I am among the ranks of the 
> > uninitiated when
> > it comes to a VNA. I can barely spell VNA. Any help would be 
> > appreciated.
> > The learning curve is steep and long.
> > 
> > 
> > Stan Rife
> > W5EWA
> > Houston, TX
> > K2 S/N 4216
> >  
> > 
> > 
> > _______________________________________________
> > vna mailing list
> > vna at lists.tapr.org
> > https://lists.tapr.org/cgi-bin/mailman/listinfo/vna
> > 
> 
> 
> _______________________________________________
> vna mailing list
> vna at lists.tapr.org
> https://lists.tapr.org/cgi-bin/mailman/listinfo/vna
>